Cuprous Oxide Solar Cell

From CleanEnergyWIKI
Revision as of 12:05, 4 April 2012 by Cmditradmin (talk | contribs) (→‎Construction)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search


K-12 Outreach Kits and Labs

Overview

Finished copper solar cell

This simple demonstration cell is actually a solar enhanced battery, but it teaches about semiconductors, electrolytes and oxidation and reduction.

When copper metal is oxidized it can take several oxidation states.

Cupric oxide with a copper(II) oxidation state is black

2 Cu + O2 → 2 CuO

cuprous oxide is with the copper(I) oxidation state is red.

4 Cu + O2 → 2 Cu2O.

Cuprous oxide is a semiconductor. It has a bandgap between it ground state and its conduction band. Without light some electrons are able to jump the band and it acts as a battery. Here are the half reactions

<math>Cu^{2+} + e^- \rightarrow Cu_{(s)} .34 V\,\!</math>

and

<math>Cu_{(s)} + O_2 \rightarrow CuO_2 -.34 V\,\!</math>


With light the cuprous oxide jumps to the conduction band and increased electricity flows. In this design the charge moves through a gelatin electroylte and to a non oxidized collection electrode. Using a gelatin electrolyte is less messy that a purely liquid electrolyte. A solid clear conductor is not great for this application because it can not make uniform contact with the copper surface.

Materials

Thincell.jpg
  • Copper foil (snail tape) from the gardening store
  • Wires and solder
  • Clear rigid plastic sheet (old cd case, or plastic lid from salad container.)
  • clear plastic packing tape
  • clear gelatin or tissue paper
  • table salt
  • volt meter


Construction

The cuprous oxide

  • Cut a 2" x 1" strip of the copper foil and remove the adhesive back.
  • Place the foil sticky side up on an stove element under a stove hood fan. When the adhesive burns off a nasty black smoke is produced be sure to do this step with ventilation or out of doors.
  • Turn the burner to high and watch as the copper foil turns from metallic to red to black. Let this cook for 10 minutes to build up a layer of oxide. The black oxide is necessary to create a protective layer that lets only a little oxygen reach the metal surface so it achieves the copper(1) oxidation state.
  • After the strip cools down gently rub the surfaced with a paper towel to flake off the black cupric oxide and reveal the red cuprous oxide underneath.




The gelatin electrolyte

Gelatin electrolyte sheet on aluminum foil
  • Make a small batch of electrolyte gelatin by mixing a packet of clear gelatin and 1/4 cup of water and a tablespoon of table salt, approximately a 15% salt solution.
  • Heat this pot on the stove or in a cup in the microwave until the solution is dissolved and clear.
  • Pour the gelatin on to a sheet of smooth sheet of aluminum foil to create a layer about 1/8" and 1/4" thick. You can fold up the edges of the foil to make a tray.
  • After the gelatin sets you should be able to peel away a leathery sheet of the material and handle it delicately.

Tissue paper electrolyte

An even simpler alternative is to sandwich a single layer of facial tissue or toilet paper between the cuprous coated electrode and the unoxidized (shiny) copper electrode. Seal the cell on 3 sides with clear packing tape so that the two electrodes have one edge exposed. Then drip the 15% salt solution into the space between the electrodes. Attache alligator clips to the two electrodes. The tissue paper holds the electrolyte against the oxide layer and the shiny electrode and it virtually transparent thus letting light through.


Assembly

regular and oxidized electrodes
  • Cut a 2" x 1" U shaped conductor from a new piece of copper tape.
  • Solder a wire to one corner of the U shaped electrode
  • Clean a corner with sandpaper and solder another wire to one corner of oxidized strip.
  • Cut a piece 3"x 2" of rigid plastic.
  • Attach the a strip or U shaped electrode of new copper to the rigid plastic using the adhesive on the back of the copper.
  • Gently cut a 1" x 2" section of gelatin electrolyte with a knife and place this on the shiny electrode.
  • Place the oxidized copper strip on top of the gelatin electrolyte making sure that it is completely separated from the shiny electrode by the gelatin layer
  • Take single piece of plastic packing tape and carefully cover the electrode and gel sandwich so that the tape seals to the plastic sheet on all sides. This prevents the gelatin from drying out and helps keep the electrodes in contact with the gel layer.
regular and oxidized electrodes


Testing

  • Now measure the current from the two wires.
  • Place the cell under a bright light. You should see the current increase under the light.

Links

Cuprous Oxide Cell in pop bottle

Cuprous Oxide Foil Cell flat version

Advance synthesis

filter paper method

[=1454&path[]=1329 JSTEM Solar Cell and the Experimental Method]